EVIL ENERGY 4-inch Cold Air Intake Kit For 2003-2007 Ford 6.0 Powerstroke Diesel F250 F350 F450 F550

Evil Energy 6.0 Powerstroke Cold Air Intake Kit | Best Cold Air Intake for 6.0 Powerstroke

This 6.0 Powerstroke cold air intake is built for enthusiasts chasing power upgrades. The kit features lightweight polished mandrel-bent aluminum piping, offered in black or red finish, paired with a premium washable and reusable high-flow cone air filter. It relocates the filter outside the engine bay to draw in cooler, oxygen-dense air. Resonance-tuned piping cuts intake restriction, delivering 7%-10% more horsepower and 6%-8% higher torque. It improves low-to-mid range throttle response and creates a deep aggressive intake tone.

All mounting hardware is included for straightforward DIY installation with basic tools, no extra parts required. It is the best cold air intake for 6.0 Powerstroke owners looking for a budget-friendly intake upgrade to sharpen throttle feel and unlock sporty engine sound.

Upgraded All-In-One 6.0 Powerstroke Air Intake & Intercooler Pipe Combo

For turbo enthusiasts seeking deep modifications, you can choose this integrated 6.0 Powerstroke air intake and intercooler pipe combo on the page, available in black kit or red aluminum pipes. The cold air intake pulls in cooler air to boost combustion efficiency, sharpen throttle response and deliver a rich sporty intake note. The matched intercooler pipe reliably transports hot pressurized air from the turbo to the intercooler, lowering charged air temperature and minimizing turbo lag.

This dual setup optimizes both the front intake path and turbo cooling circuit to fully unleash your 6.0 Powerstroke turbo engine’s performance potential. All fittings and hardware come pre-packaged for DIY installation. Ideal for 6.0 Powerstroke drivers wanting a one-time full upgrade of intake and turbo piping for stronger acceleration and consistent sustained power output.

How to Install This 6.0 Powerstroke cold Air Intake?

Before installing the EVIL ENERGY 4-inch 6.0 powerstroke cold air intake, confirm your truck’s fitment and compare the supplied parts with the factory intake. Let the engine cool, turn it off, and disconnect the negative battery cable(s).

1. Remove the factory intake. Note the original sensor, breather hose, and bracket positions. Release the sensor connector, loosen the clamp at the turbo inlet, disconnect the breather hose, and remove the factory air box and intake tube. Keep debris out of the exposed turbo inlet.
2. Preassemble the new intake. Fit the support bracket and prepare the sensor mounting area before placing the tube in the truck. Transfer the factory intake sensor to the designated mount using the correct seal and hardware. Make sure the couplers are fully seated and the hose clamps are correctly positioned; leave the bracket and clamps loose enough for final alignment. Do not overtighten the small sensor screws.
3. Position the tube and filter. Seat the new tube at the turbo inlet and attach the filter. Slightly adjust the support bracket as needed to clear the MAP sensor and its wiring. The bracket must not press against or pinch either one.
4. Reconnect and secure everything. Reconnect the intake sensor and breather hose. Once the tube and filter have clearance from nearby parts, tighten the bracket fasteners and hose clamps according to the supplied instructions.
5. Check the installation. Reconnect the battery, start the engine, and check for air leaks, unusual rubbing, or warning lights. After a short drive, recheck the clamps, bracket, and filter position.

Preparing Your 6.0 Powerstroke for Towing? Check the Radiator

Before a long tow or steep-grade trip, visible radiator seepage is a reason to address cooling-system service before it becomes a roadside stop. If your 2003–2007 F-250, F-350 or F-450 with a 6.0L Power Stroke has a confirmed radiator fault while you are planning this cold air intake installation, review EVIL ENERGY’s 2-row 48mm radiator. Match the truck’s year, radiator dimensions and hose connections before ordering.

Brand Summary

Return Reasons

1. Quality Issues: Provide photos/videos; we cover return shipping.
2. Wrong Item Ordered: Buyer covers return shipping; email within 30 days.
3. Change of Mind: Buyer covers return shipping; email within 30 days.
4. Shipping Damage: Inspect packages; do not sign for damaged items.
5. Incorrect Item Shipped: Contact within 7 days.

Price Protection Policy

Effective from August 25, 2024. Price drops within 7 days of purchase can be claimed.

Disclaimer

EVIL ENERGY reserves the right to interpret, modify, or terminate this policy in accordance with applicable laws and regulations.

If you need further information or assistance, feel free to ask!