Subscribe now to unlock $9.99 deals
| Material | 1060 Grade Aluminum (ASTM B210 Compliant) |
| Outer Diameter | 3/8" (9.5 mm) or 5/16" (8 mm) |
| Inner Diameter | 0.32" (8.1 mm) or 0.26" (6.6 mm) |
| Wall Thickness | 0.05" (1.4 mm) |
| Length | 25 FT / 10 FT |
| Working Pressure | 700 PSI |
| Burst Pressure | 2000 PSI |
| Temperature Range | -58°F to 392°F (-50°C to 200°C) |
| Features | Lightweight, Flexible, Corrosion-Resistant, Thermally Conductive |
| Applications | • Fuel Line / Return Line • Transmission Oil Line • Automotive AC Line • Air Compressor Tubing • E85 / Gas / Diesel / Water |
| Kit Includes | • 25 FT or 10 FT Aluminum Tubing • 1 × Tube Cutter • 1 × Tube Bender • 1 × Deburring Tool • 4 × Tube Clamps (3/8" or 5/16", matching the selected tube size) • 6 × 6AN Female to Compression Fittings (3/8" or 5/16", matching the selected tube size) |
The EVIL ENERGY 1060 aluminum fuel line kit is a lightweight, durable solution for high-pressure automotive fluid systems. Whether you are routing fuel, transmission oil, or air, this 25 FT or 10 FT aluminum hard line offers excellent corrosion resistance, heat transfer, and flexibility. Rated to 700 PSI working pressure and 2000 PSI burst, the coiled tubing is ideal for E85, diesel, gas, or AC retrofits. The kit includes essential tools (cutter, bender, deburring tool) so you can shape and install the line with ease. Perfect for LS swaps, restorations, or performance upgrades.

This 3/8 aluminum fuel line also comes as a 5/16 aluminum fuel line, each with a matching set of 6AN compression fittings. Both sizes replace aged hard line or build a clean custom route without buying the tools separately.
Start with engine power and fuel type, then measure the route from the tank to the engine. E85 needs more fuel flow than gasoline, so step up one line size when running E85. The 3/8" tube has about 50% more flow area than the 5/16" tube.
Fits engine-bay runs, transmission cooler lines, and repairs to one section of hard line.
Suits a tank-to-engine run. Measure the full route and double the length if the build needs both feed and return lines.

Excellent formability: 1060 aluminum tubing bends easily, which suits DIY fuel line routing.
Protective oxide layer: the aluminum surface resists corrosion in humid environments.
Thermal conductivity: the tube suits transmission and other heat-transfer lines.
Lightweight structure: aluminum has about one-third the density of steel, which trims weight on long runs.
Most street fuel systems run far below the tube rating. A high pressure aluminum fuel line rated at 700 PSI working pressure leaves a wide margin above common carburetor and EFI settings, including a typical 50 PSI or 58 PSI setup.
700 PSI working pressure compared with a 58 PSI EFI fuel system
One order covers the tubing, the tools, and the aluminum fuel line fittings. Six 6AN compression fittings are enough for three separate runs with a fitting on both ends, and four tube clamps secure the line along the chassis.
Long routes usually need more support points. Add extra mounts from the hose and tube management range when the line runs the length of the vehicle.

Plan the route first, then work through four steps using the tube bender, tube cutter, and deburring tool in the kit.


Seat the tube in the 3/8", 5/16", or 1/4" groove of the tube bender and close the handles slowly.
A slow, steady bend keeps the tube round and helps prevent kinks.
Confirm the length before cutting. Rotate the tube cutter around the aluminum tube and tighten a little at a time for a square end.


Clean the inside edge with the deburring tool so the tube end is smooth and metal chips stay out of the fuel system.
Slide on the compression fitting, tighten with an AN wrench, and connect the fitting adapters.
Install the line in place, secure it with the clamps, and pressure-check for leaks before driving.


These aluminum fuel line compression fittings clamp onto the tube on one side, so the hard line needs no flaring tool. The other side is a 6AN female 9/16 UNF thread that seals on a SAE 37-degree flare.
Each compression fitting connects only to stainless steel or aluminum hard line of the same size. Need a different end? See the AN hardline fittings for male, 90-degree, and tube nut and sleeve styles.
The right hard line depends on the route, the tools on hand, and the type of build. Compare the main fuel line materials before choosing.
| Comparison | 1060 Aluminum Fuel Line | Steel Fuel Line | Stainless Fuel Line | Nickel-Copper Fuel Line |
|---|---|---|---|---|
| Density (lighter is lower) | 2.7 g/cm³ | about 7.85 g/cm³ | about 8.0 g/cm³ | about 8.9 g/cm³ |
| Bending | Bends by hand with the included tube bender | Needs a sturdy tube bender | Hardest to bend, usually a heavy-duty bender | Bends easily by hand or with a small bender |
| Corrosion protection | Natural protective oxide layer | Relies on plating or coating | High corrosion resistance | High corrosion resistance |
| Common connection | Compression fittings included in this kit | Flare, tube nut and sleeve | Flare with a stainless-rated tool | Flare, tube nut and sleeve |
| Good match for | Custom fuel, return and transmission lines | Factory-style chassis lines | Long-life show and race builds | Restoration fuel and brake lines |

Formed aluminum tubing for fuel lines handles feed and return plumbing on gas, diesel, and E85 builds. The same coil also works for transmission oil lines, automotive AC lines, air compressor tubing, and water lines.
The thermal conductivity of 1060 aluminum supports efficient heat exchange in an automotive AC line, connecting components such as the evaporator and condenser in custom or retrofit systems.
Have the refrigerant recovered with proper equipment before opening an AC system, then evacuate and recharge the system after the new line is installed.

Pair the hard line with the components that keep fuel clean, moving, and at the right pressure.
Catch debris before fuel reaches the rail or carburetor.
Match pump flow to engine power and fuel type.
Hold steady pressure for EFI or carburetor setups.
Start from a matched fuel system for an LS engine swap.
| Policy | Details |
|---|---|
| Cancellation Policy | Orders can be canceled within 48 hours of placement. Refund processed in 3-5 business days. |
| Returns Policy | Returns accepted within 180 days. Full refund within 90 days; 15% fee for 90-180 days. |
| Non-Returnable Items | Only regular-priced items are eligible for refunds; sale items are non-refundable. |
| Refund Processing | If no refund received, check your bank/credit card. For ongoing issues, contact support@ievilenergy.com. |
Effective from August 25, 2024. Price drops within 7 days of purchase can be claimed.
EVIL ENERGY reserves the right to interpret, modify, or terminate this policy in accordance with applicable laws and regulations.
If you need further information or assistance, feel free to ask!
No Amazon reviews available for this product.