EVIL ENERGY Cold Air Intake & 85mm Electronic Throttle Body Kit for 2019-2024 Dodge Ram 1500 5.7L HEMI

2019-2024 Ram 1500 5.7L HEMI Intake & 85mm Throttle Body Kit

A heat-exposed factory intake path or an aging electronic throttle body can leave a 5.7L HEMI intake service incomplete when only one section is addressed. This EVIL ENERGY bundle pairs a vehicle-specific cold air intake with heat shield, washable filter, and pre-filter with a silver 85mm electronic throttle body and integrated TPS for owners modifying or refreshing the intake path on the specified 2019-2024 Ram 1500.

The air filter, intake tube, and throttle body work in sequence, but they remain separate interfaces that must be checked as a system. The intake supplies filtered air toward the throttle body, while the drive-by-wire throttle body meters that airflow under ECU control. Final operation also depends on coupler sizing, the intake-manifold opening, gasket sealing, sensor placement, electrical connector, vacuum connections, throttle relearn requirements, calibration, and the condition of the remaining engine-management system.

Why Pair the Ram 1500 Intake and Throttle Body?

• One connected inlet path: The intake tube and throttle body are adjacent components, so coupler engagement, clamp range, sensor orientation, flange sealing, and clearance should be checked together.
• Vehicle-specific intake hardware: The cold air intake uses an aluminum tube, steel heat shield, washable synthetic filter, and pre-filter for the covered 5.7L HEMI engine bay.
• Electronic throttle control: The 85mm throttle body uses a six-pin 1 × 6 connector and an integrated 0-5 V Hall-effect TPS.
• Coordinated installation inspection: Servicing both areas together provides one opportunity to inspect the intake couplers, clamps, breather connections, throttle flange, connector, and possible air-leak points.
• Controlled bundle scope: Fitment is limited to the 2019-2024 Dodge Ram 1500 5.7L HEMI row shown above.

Cold Air Intake for the 5.7L HEMI Ram 1500

The intake kit uses a large-diameter aluminum tube, a washable multi-layer synthetic non-woven filter, a pre-filter, and a steel heat shield. The product page lists over 98% particulate filtration efficiency and a vehicle-specific layout for the covered Ram 1500 5.7L engine bay.

Before installation, preserve the correct sensor orientation, compare the supplied hardware with the original layout, and confirm clearance around the hood, radiator support, hoses, wiring, and accessory drive. The product page does not separately identify Classic and newer-body configurations, so compare the installed air box, mounting points, inlet routing, and heat-shield area with the product photos before ordering.

85mm Electronic HEMI Throttle Body with TPS

The included silver throttle body is an 85mm electronic four-bolt unit. The product page lists an aluminum-alloy body, a six-pin 1 × 6 connector, an integrated 0-5 V Hall-effect TPS, and approximately 200 ms opening and closing response references. An idle air control motor is not included because this is an electronically actuated drive-by-wire design.

A larger throttle-body diameter increases available flow area, but it does not establish a guaranteed engine-output increase. Actual behavior depends on the intake-manifold opening, coupler geometry, engine configuration, ECU strategy, calibration, and installation quality. Confirm the electrical connector, flange, opening, gasket, and installed intake interface before removing the original throttle body.

Bundle Fitment for 2019-2024 Ram 1500 5.7L HEMI

This bundle is limited to the 2019-2024 Dodge Ram 1500 equipped with the 5.7L 345 cu. in. naturally aspirated HEMI gasoline V8. No other engine size, Ram model, or year range is included in this bundle listing.

Order from the installed hardware, not the model name alone: Confirm that the truck uses the expected six-pin single-row throttle connector and four-bolt electronic throttle-body arrangement. Engine-bay layout, air-box mounting, breather connections, calibration, and intake routing can differ with body configuration, regional specification, prior repairs, or aftermarket modifications.

Package Contents

Package boundary: No additional adapter coupler, throttle-body gasket, calibration service, or other interface part is claimed beyond the contents supplied with the two linked products. Determine any additional installation requirements from the truck's measured interfaces and service information.

Brand Summary

Return Reasons

1. Quality Issues: Provide photos/videos; we cover return shipping.
2. Wrong Item Ordered: Buyer covers return shipping; email within 30 days.
3. Change of Mind: Buyer covers return shipping; email within 30 days.
4. Shipping Damage: Inspect packages; do not sign for damaged items.
5. Incorrect Item Shipped: Contact within 7 days.

Price Protection Policy

Effective from August 25, 2024. Price drops within 7 days of purchase can be claimed.

Disclaimer

EVIL ENERGY reserves the right to interpret, modify, or terminate this policy in accordance with applicable laws and regulations.

If you need further information or assistance, feel free to ask!